abs error toaf

[livan]

hello friends for a while I'm using this machine.
I do diagnosis and he gives me several airbag errors
I already change the contacts under the seats, but the error persists,
someone can tell me what is wrong
thank you very much
I write from Spain and I use a translator, apologies

[livan]

[baconbuttyman]

When you say changed the contacts. Dhave you hard wired them in?

[baconbuttyman]

Also. My car was putting out some error codes. After they were supposedly fixed. Had to clear the ecu of fault codes to get new readings. The codes never came back

[livan]

Hello Friend
I mean, change the connectors for better ones
I had read that it could be a problem with poor connectors
but there is the fault
Thank you

[livan]

Maybe the ecu of the airbag is blocked?
Have I ever read some data crash?
but my car has never had accidents
everything started one day when moving the driver's seat, then the light went on
I really appreciate your help
next month I have the mot, and I need to fix it

[livan]

bueno hoy saque volante para comprobar si era del carrete el fallo pero no
asi que sigo con estos fallos
solo me queda ir a un desguace a por una centralita de airbag y probar

[Spike]

¡Hola Livan! ¿Quizás es cuando mueves el asiento que el conector se separa de nuevo?

[Spike]

Si todo parece estar bien con el conector, desconectes la batería por 20 minutos

[livan]

hola amigo
los conectores los compre nuevos,y los renové
la bateria la desconecte durante toda la noche,pero sigue igual
ire a ver a un amigo que tiene otro sistema de diagnosis,ojala tenga suerte
gracias

[livan]

nadie puede arrojar algo de luz?
I recently wrote to the creator of the program, I need you to help me

[Mal7921]

If the ABS light is not on, it may be an error that has been fixed but still logged. The clear button towards the top of the TOAF window will clear all the errors. If the error returns, it will show which sensor is giving the fault.

Hope that helps :-)

[livan]

If the ABS light is not on, it may be an error that has been fixed but still logged. The clear button towards the top of the TOAF window will clear all the errors. If the error returns, it will show which sensor is giving the fault.

Hope that helps :-)

thanks friend,
the light is not erased, in the photographs, the number 2 leaves the errors thrown by the vehicle, it does not say which sensor is failing,
thanks friend
in August I have the MOT, I hope I can fix it befores

[Mal7921]

Can you post a screenshot with the error in TOAF?

One way to narrow it down, if the speedo isn’t working then it’s the front right sensor, if you attach an obd II dongle and use Torque or Torque Pro on an android phone and can’t get speed data drom the OBD port, it’s the front left sensor.

I’ve a spare front and spare rear sensor if you want to try swapping them out to test

[livan]

Hello Friend
thanks, the speedometer if it works, it correctly marks me the speed
I already have a replacement for ywc107090
next week, I am about to assemble the unit. I will tell you what happens
Thank you

If everything stays the same I will move 80km to a session of t4

[Mal7921]

Just went to the beginning, the airbag is srs which confused me as I’ve just looked at abs errors on my car.

So srs, which would include the airbags, could have been caused by the seat being moved if the wiring snapped due to pressure. Some cars such as the jaguar x type had issues with wires fraying because they were routed under the seat rails.

Check where the wiring goes, if it goes under or near the seat runner, see if you can pull or push the wiring so you can see if it’s been crushed or rubbed over time. This could break the wires or some of the wires, causing an error. If this is the case, the wire or wires will need to be extended slightly and rejoined.

If some wires are broken, it could cause unusual errors as the car partly detects the airbag or seatbelt pre-tensioner.

[livan]

Hello Friend
today I had time to look
Today I was able to discover, that perhaps it is proble of the rear pretensioner, since in that position is the seat of my little girl
It is possible that it was pulled hard from the belt, and that is why the machine gave me that error
the next week I will disassemble rear seats, and check
thanks friend

[livan]

es posible que ya casi este solucionado
hoy e desconectado los cinturones traseros,y parece que ya no me sale el error de ignicion circuit ic11
queda revisar el pirotecnico del pilar a,que se rompio el conector al comprobar